Schneider Electric PC0984380 Power Supply
The Schneider Electric PC0984380 is a 24 VDC industrial power supply designed to convert AC input power into regulated DC power for control equipment and connected loads. It accepts an AC input range of 85-264 VAC and delivers 5.0 A continuous output, with a peak capability of 7.5 A for 2 seconds. The unit supports DIN rail or panel mounting and includes multiple electrical protection functions.
AC Input and DC Output
The PC0984380 accepts an AC supply from 85 VAC to 264 VAC at 47-63 Hz, allowing operation across a wide range of AC supply conditions. Its regulated output is 24 VDC with a stated tolerance of +/-3%.
The supply provides 5.0 A continuous output current and supports peak loads of up to 7.5 A for 2 seconds. This peak rating is relevant when connected equipment draws temporary additional current during startup or switching.
Two screw terminals provide the positive and negative DC output connections. The green DC OK LED indicates the output status.
Electrical Performance and Protection
The PC0984380 has a typical efficiency of 88% at 230 VAC input and a power factor greater than 0.95 at full load. Its output ripple and noise are specified below 120 mV peak-to-peak, while the hold-up time is 25 ms at a 5 A load.
Built-in protection covers overvoltage, overcurrent, short-circuit, and overtemperature conditions. The internal fuse arrangement provides additional protection against electrical faults.
Installation and Mounting
The power supply supports installation on a standard 35 mm DIN rail or direct panel mounting using two M4 screws. AC input connections are made through the L, N, and Earth terminals, while the DC load connects to the positive and negative screw terminals.
For cooling, maintain at least 40 mm of free space above and below the unit. Ventilation openings must remain unobstructed during operation to support heat dissipation.
Energy Storage and Maintenance
The output filter capacitors have a combined capacitance of 330 uF. These capacitors retain electrical charge after AC power is disconnected, so the supplied installation information specifies a 10-second discharge waiting period before handling the internal circuitry.
The internal component configuration includes six capacitors, eight diodes, four transistors, one transformer, and two fuses. These components form the power conversion, filtering, and protection circuits.
Environmental Operating Conditions
The PC0984380 is specified for operation from -20 deg C to +60 deg C. Above 50 deg C, the output current must be reduced linearly, reaching 3 A at 60 deg C.
The circuit board has a conformal coating intended to provide additional protection against moisture exposure. However, the available specifications do not establish an enclosure protection rating, so the coating should not be interpreted as making the complete power supply waterproof.
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | PC0984380 |
| Brand | Schneider Electric |
| Product Type | Industrial Power Supply |
| AC Input Voltage | 85-264 VAC |
| Input Frequency | 47-63 Hz |
| DC Output Voltage | 24 VDC +/-3% |
| Continuous Output Current | 5.0 A |
| Peak Output Current | 7.5 A for 2 seconds |
| Output Connector | 2 screw terminals (+, -) |
| Efficiency | 88% typical at 230 VAC input |
| Power Factor | Greater than 0.95 at full load |
| Ripple and Noise | Less than 120 mV peak-to-peak |
| Hold-up Time | 25 ms at 5 A load |
| Output Filter Capacitance | 330 uF total |
| Protection | Overvoltage, overcurrent, short-circuit, overtemperature |
| Status Indicator | 1 green DC OK LED |
| Mounting | 35 mm DIN rail or panel screws |
| Panel Mounting Hardware | 2 M4 screws |
| Cooling Clearance | 40 mm above and below |
| Operating Temperature | -20 deg C to +60 deg C |
| Temperature Derating | Linear derating above 50 deg C to 3 A at 60 deg C |
| Circuit Board Protection | Full conformal coating |
| Dimensions (W x H x D) | 5.5 x 12.5 x 11.0 cm |
| Dimensions (W x H x D) | 2.17 x 4.92 x 4.33 in |
| Weight | 0.85 kg (1.87 lb) |
| Internal Components | 6 capacitors, 8 diodes, 4 transistors, 1 transformer, 2 fuses |
Frequently Asked Questions
Q: Can the PC0984380 supply 7.5 A continuously?
A: No. Its continuous output rating is 5.0 A. The 7.5 A output is permitted only as a short-duration peak lasting up to 2 seconds.
Q: How much ventilation clearance is required when installing the PC0984380?
A: Maintain at least 40 mm of free space above and below the power supply. Keep the housing ventilation openings unobstructed to support cooling.
Q: How long should I wait before handling the PC0984380 after disconnecting AC power?
A: Allow at least 10 seconds after AC power removal, as specified in the supplied information. The output filter capacitors have a combined capacitance of 330 uF and may retain electrical charge.
Schneider Electric PC0984380 Power Supply
Schneider Electric PC0984380 Power Supply
The Schneider Electric PC0984380 is a 24 VDC industrial power supply designed to convert AC input power into regulated DC power for control equipment and connected loads. It accepts an AC input range of 85-264 VAC and delivers 5.0 A continuous output, with a peak capability of 7.5 A for 2 seconds. The unit supports DIN rail or panel mounting and includes multiple electrical protection functions.
AC Input and DC Output
The PC0984380 accepts an AC supply from 85 VAC to 264 VAC at 47-63 Hz, allowing operation across a wide range of AC supply conditions. Its regulated output is 24 VDC with a stated tolerance of +/-3%.
The supply provides 5.0 A continuous output current and supports peak loads of up to 7.5 A for 2 seconds. This peak rating is relevant when connected equipment draws temporary additional current during startup or switching.
Two screw terminals provide the positive and negative DC output connections. The green DC OK LED indicates the output status.
Electrical Performance and Protection
The PC0984380 has a typical efficiency of 88% at 230 VAC input and a power factor greater than 0.95 at full load. Its output ripple and noise are specified below 120 mV peak-to-peak, while the hold-up time is 25 ms at a 5 A load.
Built-in protection covers overvoltage, overcurrent, short-circuit, and overtemperature conditions. The internal fuse arrangement provides additional protection against electrical faults.
Installation and Mounting
The power supply supports installation on a standard 35 mm DIN rail or direct panel mounting using two M4 screws. AC input connections are made through the L, N, and Earth terminals, while the DC load connects to the positive and negative screw terminals.
For cooling, maintain at least 40 mm of free space above and below the unit. Ventilation openings must remain unobstructed during operation to support heat dissipation.
Energy Storage and Maintenance
The output filter capacitors have a combined capacitance of 330 uF. These capacitors retain electrical charge after AC power is disconnected, so the supplied installation information specifies a 10-second discharge waiting period before handling the internal circuitry.
The internal component configuration includes six capacitors, eight diodes, four transistors, one transformer, and two fuses. These components form the power conversion, filtering, and protection circuits.
Environmental Operating Conditions
The PC0984380 is specified for operation from -20 deg C to +60 deg C. Above 50 deg C, the output current must be reduced linearly, reaching 3 A at 60 deg C.
The circuit board has a conformal coating intended to provide additional protection against moisture exposure. However, the available specifications do not establish an enclosure protection rating, so the coating should not be interpreted as making the complete power supply waterproof.
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | PC0984380 |
| Brand | Schneider Electric |
| Product Type | Industrial Power Supply |
| AC Input Voltage | 85-264 VAC |
| Input Frequency | 47-63 Hz |
| DC Output Voltage | 24 VDC +/-3% |
| Continuous Output Current | 5.0 A |
| Peak Output Current | 7.5 A for 2 seconds |
| Output Connector | 2 screw terminals (+, -) |
| Efficiency | 88% typical at 230 VAC input |
| Power Factor | Greater than 0.95 at full load |
| Ripple and Noise | Less than 120 mV peak-to-peak |
| Hold-up Time | 25 ms at 5 A load |
| Output Filter Capacitance | 330 uF total |
| Protection | Overvoltage, overcurrent, short-circuit, overtemperature |
| Status Indicator | 1 green DC OK LED |
| Mounting | 35 mm DIN rail or panel screws |
| Panel Mounting Hardware | 2 M4 screws |
| Cooling Clearance | 40 mm above and below |
| Operating Temperature | -20 deg C to +60 deg C |
| Temperature Derating | Linear derating above 50 deg C to 3 A at 60 deg C |
| Circuit Board Protection | Full conformal coating |
| Dimensions (W x H x D) | 5.5 x 12.5 x 11.0 cm |
| Dimensions (W x H x D) | 2.17 x 4.92 x 4.33 in |
| Weight | 0.85 kg (1.87 lb) |
| Internal Components | 6 capacitors, 8 diodes, 4 transistors, 1 transformer, 2 fuses |
Frequently Asked Questions
Q: Can the PC0984380 supply 7.5 A continuously?
A: No. Its continuous output rating is 5.0 A. The 7.5 A output is permitted only as a short-duration peak lasting up to 2 seconds.
Q: How much ventilation clearance is required when installing the PC0984380?
A: Maintain at least 40 mm of free space above and below the power supply. Keep the housing ventilation openings unobstructed to support cooling.
Q: How long should I wait before handling the PC0984380 after disconnecting AC power?
A: Allow at least 10 seconds after AC power removal, as specified in the supplied information. The output filter capacitors have a combined capacitance of 330 uF and may retain electrical charge.
