Honeywell CC-TAIL51 Input Modules
The Honeywell CC-TAIL51 , also cataloged as the CC-TAIL51 LLAI IOTA Module, operates as a dedicated hardware component for 16-channel low-level analog input signal termination within Honeywell Experion PKS platforms.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | CC-TAIL51 |
| Brand | Honeywell |
| Origin | USA |
| Weight | Standard Series C IOTA Weight |
| Dimensions | 9 in (229 mm) length |
| Operating Temp | -40 deg C to +70 deg C |
| Power Consumption | Passive backplane loop powered / 24 VDC |
| Channel Capacity | 16 Channels |
| Module Integration | Supports CC-TUIO51 and CC-TUIO41 modules |
| Configuration Type | Low Level Analog Input (LLAI) Non-Redundant |
Field Loop Signaling & Channel Isolation
The CC-TAIL51 termination assembly incorporates high-density circuit routing designed to preserve low-level analog signal integrity across all 16 input channels. Engineered to maintain channel-to-channel isolation, the board prevents ground loops and electrical interference from degrading thermocouple and millivolt sensor measurements. It supports bi-directional 4-20 mA HART loop protocol routing and passes high-frequency digital instrument diagnostics directly to connected CC-TUIO51 and CC-TUIO41 processing units without signal attenuation.
Frequently Asked Questions
Q: Which I/O processing modules are electrically compatible with the CC-TAIL51 baseboard?
A: The CC-TAIL51 assembly is specifically designed to interface directly with CC-TUIO51 and CC-TUIO41 universal input/output modules.
Q: Is the CC-TAIL51 configured for redundant module mounting?
A: No, the CC-TAIL51 is a single-slot, non-redundant Low Level Analog Input (LLAI) Input Output Termination Assembly (IOTA).
Field Installation Guidelines
- Isolate all 24 VDC external loop power feeds prior to securing or removing the 9-inch assembly on the mounting channel.
- Fasten the base plate to the cabinet carrier frame using dedicated retention screws to maintain a metallic ground path to chassis earth.
- Route field input sensor cables through designated wire channels, bonding shield drain wires to the main cabinet grounding bar.
- Check pin alignment carefully before seating the CC-TUIO51 or CC-TUIO41 module onto the card-edge connector to prevent terminal strain.
Honeywell CC-TAIL51 Input Modules
Honeywell CC-TAIL51 Input Modules
The Honeywell CC-TAIL51 , also cataloged as the CC-TAIL51 LLAI IOTA Module, operates as a dedicated hardware component for 16-channel low-level analog input signal termination within Honeywell Experion PKS platforms.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | CC-TAIL51 |
| Brand | Honeywell |
| Origin | USA |
| Weight | Standard Series C IOTA Weight |
| Dimensions | 9 in (229 mm) length |
| Operating Temp | -40 deg C to +70 deg C |
| Power Consumption | Passive backplane loop powered / 24 VDC |
| Channel Capacity | 16 Channels |
| Module Integration | Supports CC-TUIO51 and CC-TUIO41 modules |
| Configuration Type | Low Level Analog Input (LLAI) Non-Redundant |
Field Loop Signaling & Channel Isolation
The CC-TAIL51 termination assembly incorporates high-density circuit routing designed to preserve low-level analog signal integrity across all 16 input channels. Engineered to maintain channel-to-channel isolation, the board prevents ground loops and electrical interference from degrading thermocouple and millivolt sensor measurements. It supports bi-directional 4-20 mA HART loop protocol routing and passes high-frequency digital instrument diagnostics directly to connected CC-TUIO51 and CC-TUIO41 processing units without signal attenuation.
Frequently Asked Questions
Q: Which I/O processing modules are electrically compatible with the CC-TAIL51 baseboard?
A: The CC-TAIL51 assembly is specifically designed to interface directly with CC-TUIO51 and CC-TUIO41 universal input/output modules.
Q: Is the CC-TAIL51 configured for redundant module mounting?
A: No, the CC-TAIL51 is a single-slot, non-redundant Low Level Analog Input (LLAI) Input Output Termination Assembly (IOTA).
Field Installation Guidelines
- Isolate all 24 VDC external loop power feeds prior to securing or removing the 9-inch assembly on the mounting channel.
- Fasten the base plate to the cabinet carrier frame using dedicated retention screws to maintain a metallic ground path to chassis earth.
- Route field input sensor cables through designated wire channels, bonding shield drain wires to the main cabinet grounding bar.
- Check pin alignment carefully before seating the CC-TUIO51 or CC-TUIO41 module onto the card-edge connector to prevent terminal strain.
